Switch material

Smoke detectors Smoke detectors can save lives and belong to any household. After Wds 2344:2014-07, Wds 3131:2010-05, EN 14604:2005 + AC:2008, wfdb 14/01:2010-05; (reference number G 216023). Incl. Q-label (licence number: 2016-0079). Easy and easy installation. 24 hours protection. Protection: IP20. Test switches. Optical sensor; fast reaction. Still alarm / break function. Battery 3 WDC / CR123A Lithium fixed or non-replaceable. Battery life 10 years. Low battery level indicator. 3 years warranty. Color: Pure white similar to RAL 9010. Operating temperature: 4 to 38° C. Humidity: 25 to 85%. Alarm signal strength: greater than 85 db at 3 m. Room size: 20 to 40 m2. Dimension Smoke detector (Øxh): approx. 100 x 35 mm. Minimum order quantity: 1 piece

Twilight switch Compact For wall and mast mounting. With built-in light catcher. Suitable for external mounting. Cable cross-section up to 2.5 square meters. Cable diameter up to 11 mm. LED for displaying brightness. Opal UV protective cover. Suitable for protection (IP): IP65 Max. Switching current (ohmic load): 16 A type of sensor: light sensor built-in rated voltage: 230 W contacts: 1 closer color: white switch-on brightness: 2 - 200 lx Max. Switching power: 4000 W

Light collector PDSLE for distribution installation. Suitable for external mounting. Cable cross-section up to 2.5 square meters. LED for displaying brightness. LED operating indicator. Opal UV protective cover. Suitable for protection (IP): IP65 turn-on delay: 8 s Max. Switching current (ohmic load): 16 A type of sensor: light sensor separately rated voltage: 230 W contacts: 1 closer color: white switch-on brightness: 2 - 100 lx Max. Switching power: 4000 W

Replacement light collector for PDSL100 and PDSL10000 Suitable for protection (IP): IP65 Color: white

Motion detector for wall mounting Housing made of high-quality and UV-resistant polycarbonate, dimensions: L91 x B67 x H80 mm, wall mounting. Basic load - LED 6W Max. Range to one side: 12 m Monitoring range: 140 ° Color: white Rated voltage: 230 W Protection type (IP): IP44 Assembly type: Applicable response brightness: Yes Min. Switching time: 4 s Max. Switch-on time: 10 min Response brightness: 2 - 2000 lx Max. Switching power: 1000 W Temperature range: -25 - 50 °C

Motion detector for wall mounting Housing made of high-quality and UV-resistant polycarbonate, dimensions: L91 x B67 x H80 mm, wall mounting. Basic load - LED 6W Max. Range to one side: 12 m Monitoring range: 140 ° Color: brown Rated voltage: 230 W Protection type (IP): IP44 Assembly type: Applicable response brightness: Yes Min. Switching time: 4 s Max. Switch-on time: 10 min Response brightness: 2 - 2000 lx Max. Switching power: 1000 W Temperature range: -25 - 50 °C

Socket IP 54. For installation of the PPMMAP and PPMSAP presence detector. To increase the degree of protection to IP 54. Dimensions: diameter 100 x height 15 mm. Version: Onput housing

All settings on the motion detector can be done conveniently from the ground (without annoying conductor setting). Suitable for PBM 280 motion detectors. Due to numerous functions, the motion detector can be adapted at any time, even later. Version: Remote control

Heat detectors heat detectors can save lives and belong to any household, signal triggering: heat/heat, alarms safely and reliably at too high temperature, continuous monitoring: constantly monitors the air temperature, detects: no smoke, no gas or fire, especially for smokey and humid areas where permanent steam development occurs, such as kitchen, bathroom, garage, sleeping room, etc. 24 hours protection, easy and easy assembly, assembly recommendation: On the ceiling or above on a wall, mounting: wireless, heat sensor reacts at over 57 °C, 85dB alarm signal (extra loud,) test button for function testing, incl. 9 volt battery, battery life approx. 1 year, battery control indicator: warning message with too weak battery, operating temperature: 0 - 70 °C, operating humidity: 25 - 95 %, dimensions: Ø107 x 43 mm Colour: pure white RAL number (similar): 9010

Mounting kit for smoke detectors and heat detectors with this magnetic adhesive system is easy, fast and clean installation of a smoke detector or heat detector without screws or drilling, especially for camping, boat or special ceilings (concrete,) everywhere mountable, without tools, fits almost all smoke detectors, Ø of mounting plate: 70 mm, Ø detector: 80 mm, mounting: support plate (without magnets): Remove the protective film, attach to the ceiling and press for at least 10 seconds, magnetic plate: Remove the protective film, attach to the smoke/heat detector and at least. Apply 10 seconds of light pressure, the smoke/heat detector with the magnetic plate is then attached to the carrier plate, assembly area: stable, dry, dust-free and greasy, Not for: vinyl wallpaper, polystyrene, non-stick and silicone coatings, installation requirements for smoke detectors according to Wds note, material: steel. Load capacity: 2.1 kg.

Remote control for presence detectors all settings on the presence detectors can be done conveniently from the ground (without annoying conductor setting up), suitable for PPMMAP presence detectors Master-AP, by numerous functions the presence detector can be adjusted at any time, also subsequently, automatic reading-on of the current insulation value or 2s test function are possible, switching on or off the luminaire by means of push buttons - an additional light switch can be omitted, a practical wall detector

Hygrostat surface hygrostat mechanical. Serves for monitoring and regulating relative humidity, e.g. in business premises, apartments, winter gardens, bathrooms, swimming pools, computer rooms. A potential-free switching contact is actuated by the action of the relative humidity on a measuring band. The set value is adjusted by means of the setting knob located on the front side. The setting range is bevelable. Number of outputs: 2. Number of control ranges: 1. Output signal2: dehumidification, switching. Humidification: 3 (0.2) A. Dehumidification: 5 (0.2) A. Switching voltage: 24-230 VAC, 50 Hz. Min. switching current: 100 ma. operating voltage: no auxiliary energy required. Average power consumption: 0 W. Adjustment range: 30 - 100. Electrical connection: screw terminals 0.5...2.5 mm2. Material housing: plastic ABS. Sensor: plastic fibers. Hysteresis: approx. 4% r.H. Mechanical range adjustment. Medium: air, not aggressive. Mounting: plaster/wall mounting (4-hole mounting on UP-Dose Ø 55 mm). Surface finish: matt. No potential. Control range: 30 o 100 %. Control function: moistening or dehumidifying switching element: microswitches. Switching contact: switch (changer). Switching power: Clamp 4: 1150 W, Clamp 2: 690 W. Protection type: IP 30. Protection class: II, after appropriate assembly. Safety and Emw: according to DIN EN 60730. Set. Degree of soiling: 2nd storage temperature: -20° to +60°C. Ambient temperature: +10° to +60°C. Permissible humidity: max. 95% r. H, not condensing. Dimensions Housing: 78.3 x 25.5 x 83.4 mm. Weight: approx. 90 g. Color Case: pure white, similar to RAL 9010. Note: Wet cell spacing according to DIN WDE 0100-701! Color: pure white Mounting type: Cleaning With thermostat: No Color: white Protection type (IP): IP30 Digital display: No Adjustment range Relative humidity: 30 - 100%

Clamping strips for heating circuit distributors, terminal strips in the housing for wiring up to 5 room thermostats and max. 20 actuators, per channel are max. 4 actuators possible, device safety T4A/250V installation dimensions. 5 x 20 mm (also secures the circuits of the connected controllers, the pump and the valve drives,) protection class: II, after appropriate assembly, operating voltage: 230 VAC, 50 Hz, assembly / fastening: plastering/wall mounting with 4 supplied fastening screws, surface condition: matt, color housing: light grey, similar RAL 7035, material housing: plastic ABS, ambient temperature: grad O 10 ... - storage. 95% r. H,. non-condensing, electrical connection: spring clamps 0.5 qmm to 1.5 qmm, when using wire end sleeves 0.25 qmm to 0.75 qmm, control function: heating or cooling

Clamping bar for heating circuit distributor, clamp bar in housing for wiring up to 8 room thermostats and max. 32 actuators, per channel are max. 4 actuators possible, device safety T6, 3A/250V installation dimensions. 5 x 20 mm (also secures the circuits of the connected controllers, the pump and the valve drives,) protection class: II, after appropriate assembly, operating voltage: 230 VAC, 50 Hz, assembly / fastening: plastering/wall mounting with 4 supplied fastening screws, surface condition: matt, color housing: light grey, similar RAL 7035, material housing: plastic ABS, ambient temperature: grad O 10 ... - storage. 95% r. H,. non-condensing, electrical connection: spring clamps 0.5 qmm to 1.5 qmm, when using wire end sleeves 0.25 qmm to 0.75 qmm, control function: heating or cooling