List of products by brand Eltako

Multifunction time relay 230W with 10 functions, 1 lock potential-free 10A/250V AC, incandescent lamps 1000W, stand-by-loss 0.4 Watt, series installation device for mounting on support rail DIN-EN 60715 TH35 Analog adjustable multifunction time relay with 10 functions. Stand-by loss only 0.4 Watt. Times between 0.1 seconds and 40 hours are adjustable. Functions F: RV = relapse delay. AV = response delay. TI = clock generator starting with pulse. TP = clock generator starting with pause. IA = impulse-controlled response delay (e.g. automatic door opener). EW = turn-on wiper. AW = switch-off wiper. ARV = response and relapse delay. ON = duration ON. OFF = duration AUS. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence. It flashes as long as the working contact is open and illuminates continuously as long as the working contact is closed. The time base T is set with the central latching rotary switch T. Width in division units: 1 control voltage 1: 230 - 230 W control voltage type 1: AC frequency of control voltage 1: 50 - 50 Hz switching power fluorescent lamps parallel: 250 VA 1. Time range from/to: 40 - 0.1 Function: Multifunction Number of locks: 1 Number of openers: 0 Number of switchovers: 0 Voltage type of supply voltage: AC Switching power bulbs: 1000 W Supply voltage range: 230 - 230 W Switching power Luminous lamps inductor: 500 VA Mounting height: 58 mm Rated current at 250 W AC: 10 A Switching power Luminous lamps DUO: 500 VA. Time unit: minutes/hour assembly type: DIN rail

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours as well as the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sinus wave, 0.1 Watt-by-adjustable time. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence. control voltage 1: 8 - 230 W control voltage type 1: AC/DC switching power fluorescent lamps parallel: 500 VA 1. Time range from/to: 40 - 0.1 Function: Relapse delay Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductor: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA. Time unit: minutes/hour assembly type: DIN rail

Current relays for mounting on support rail DIN-EN 60715 TH35, potential-free 16 A /250 W AC, stand-by loss only 0.8 Watt current relay, stand-by loss only 0.8 Watt. Mounting unit for mounting on support rail (1 TE). To this end, simply connect the N conductor to the terminal (N) and L to 1 (L). This results in an additional stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. With an internal ring core current converter, the alternating current flowing via a consumer W1 is compared with the set value from 0.1A to a maximum of 32A and, when exceeded, a relay switches off a consumer W2 connected to 2 within 0.5 seconds or a consumer W3 connected to 3. Adjustment accuracy ±5%. From 25A, the relay always switches on. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. The current base A is set with the lower latching rotary switch A. TLE: 1 Number of contacts as changer: 1 Rated control voltage Us at AC 50 Hz: 230 - W

Electronic AC meter AC counters without approval for support rail. Stand-by loss only 0.5 Watt. Accuracy class B (1) % With S0 interface. This alternating current meter measures the active energy on the basis of the current flowing between the input and the output. The own consumption of only a maximum of 0.5 watt active power is not measured and not displayed. Like all counters without PTB or MID approval in Germany not approved for monetary current billing. Every 30 seconds, the display switches from the accumulated active energy to the instantaneous consumption in Watt for 5 seconds. 1 external conductor can be connected with a current up to 32A. In the event of a load to be expected of more than 50%, a ventilation distance of 1/2 division unit is to be maintained for devices mounted next to it. If the spacer DS12 is used. The starting current is 20ma. The display can only be read with power supply. However, the consumption is non-volatile and will be displayed immediately after a power failure. Two N-terminals for secure cross wiring of several counters. The decimal point which flashes depending on the power consumption indicates a power reference. In case of false connection, false appears in the display. The digital display has 7 digits. Up to 99999,99kWh, two descendants are displayed. From 100000.0kWh only one. Even with only theoretically conceivable maximum current reference, the display would be suitable for more than 15 years. The power reference is displayed with the decimal point. TLE: 1 Certified: No Measurement voltage: 230 W

Disconnection relays with window contact 1 closer not potential-free 10A/250V AC, stand-by loss only 0.5 Watt, for installation and AP installation, hybrid technology combines the advantages of wear-free electronic control with the high power of special relays, control input with internally generated low voltage 24W DC, with a disconnection transformer galvanically separated from the power supply and the working contact (PELaisV), therefore no external low voltage. 1 lock not potential-free 10A/250V AC. With window contact. Stand-by loss only 0.5 Watt. For installation. 45mm long, 45mm wide, 18mm deep. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Control input with internally generated low voltage 24W DC. galvanically separated from the power supply and the working contact (PELV). Therefore, no external low-voltage power supply is required. With two L-terminals and 2 N-terminals for easy and fast installation. Power supply 230W. The enclosed window contact consists of a reed relay with connection terminals and a magnet. The normally closed contact opens as soon as the magnet has come closer than 25mm. Connected to the terminals T1 and T2 of the separating relay ETR61NP, the power supply of a rod train is switched on as long as the window is open. The ETR61NP can be placed in the UP-Dose behind the outlet for the Dunstabzug. Installation of the window contact FK: On the housing-painted side, lever the inserts out. Connect Reedrelais and cut out housing section for the line. Both housings maximum 15mm

Switching power supplies for mounting on support rail DIN-EN 60715 TH3Stand-by-loss 0.2 Watt, short-circuit-proof, with a load greater than 50% of the rated power and always with adjacent switching power supplies above 12 Watt rated power and with dimmers a 1/2 division of ventilation unit with spacers DS12 is required, input voltage 230W AC, -(20% to +10)%, efficiency 12W DC 83%, 24W DC. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Efficiency 12W DC 83%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function).

Power monitoring relay for mounting on support rail DIN-EN 60715 TH35, for monitoring 230 W AC voltage against the zero conductor, drop delay adjustable 0.1 to 8 seconds, draw delay 0.5 s, LED display for applied voltage, with the lower rotary switch on the front side two draw-on or respectively. Relapse voltages are set: U1: 161W drop-back voltage and 185V draw voltage U2: 196W drop-back voltage and 206W draw-on voltage according to. WDE 0100 part 718 network monitoring relay with field monitoring. Stand-by loss only 0.8 Watt. Mounting unit for mounting on support rail (2 TE). For monitoring 230W AC voltage between 1 to 3 external conductors and the neutral conductor and for monitoring the rotary field (rotating in the right) in the rotary switch positions 2ph and 3ph. In the position L1/L2/L3, only the rotary field is monitored, regardless of the mains voltage. If L1 fails, the relay will drop immediately without a relapse delay. With the lower rotary switch on the front side, two draw or. Relapse voltages are set and the number of monitored external conductors must be specified. U1: 161W falling voltage and 185V tightening voltage. U2: 196W falling voltage and 206W tightening voltage according to. WDE 0100, Part 718 (formerly: WDE 0108, Part 1). LED display for correct applied voltage. In case of incorrect polarity or a missing external conductor, the LED flashes quickly. Relapse delay RV with the upper rotary switch adjustable from 0.1 to 8 seconds. While the RV time is running, the LED flashes slowly. Suit delay 0.5s. Number of contacts as changer: 2 TLE: 2

Radio repeater for installation and AP installation, this repeater is only required if the structural conditions prevent an undisturbed reception or the distance between radio probe and receiver is too large, from work the 1-level mode is activated but also can be adjusted to level 2, radio repeater need not be learned, they receive and amplify the signals from all radio sensors in their reception area, only supply voltage required, standby level 1. Stand-by loss only 0.9 Watt. For installation. 45mm long, 45mm wide, 33mm deep. This repeater is only required if the structural conditions prevent an undisturbed reception, or the distance between radio button and receiver is too large. The 1-level mode is set from work. Only the radio signals are received, tested and transmitted with full transmission power. Radio signals from other repeaters are ignored to reduce the amount of data. The rotary switch can be switched to the 2-level mode. In addition to the radio signals from sensors, the radio signals from another 1-level repeater are also processed. A radio signal can thus be received and amplified at most twice. The LED displays incoming radio signals by short flashing. Radio-repeaters do not have to be learned. They receive and amplify the radio signals from all radio sensors in their reception area.

2-channel weekly switch clock 1+1 closer potential-free 16A/250V AC, 60 switch clock memory locations, power reserve 2 weeks, stand-by loss max. 0.4 Watt, automatic summer winter time switch and pulsed, with astro function, additional control input for the central on or off 2-channel clock with astro function. Stand-by loss only 0.03-0.4 watts. To this end, simply connect the N conductor to the terminal (N) and L to 1(L) and/or 3(L). This results in an additional stand-by loss of only 0.1 Watt. Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. Up to 60 switching clock memory locations are distributed freely on the channels. With date and automatic summer/winter time conversion. Power reserve without battery about 7 days. Each storage space can be occupied either with the astro function (automatic switching after sunrise or sunset), the switch-on and switch-off time or a pulse switching time (in which a pulse of 2 seconds is triggered). The switch-on or switch-off time Astro can be shifted ± 2 hours and, in addition, from the manufacturing week 19/2012, a time shift of up to ± 2 hours influenced by the sun. With control input +(A1) for central control ON or OFF with priority. Supply voltage and control voltage for central control 8..230V UC. The switching clock is set with the MODE and SET keys and a key lock is possible. Set language: After each application of the supply voltage, the language can be selected with SET within 10 seconds and confirmed with MODE. D = German, GB = English, F = French, IT = Italian and ES = Spanish. Then the normal display appears: weekday, time, day and month. Quick run: In the following settings, the numbers run quickly when the input key is pressed longer

Radio transmitter module for installation, radio 2x transmitter module with internal antenna, no stand-by loss radio 2x transmitter module. With internal antenna. No standby loss. For installation. 45mm long, 45mm wide, 18mm deep. The radio transmitter module FSM61-UC has two channels and can thus be radio telegrams in the Eltako- Send building radio. A1 causes a radio telegram, such as rocker, to press a radio button with a rocker and A3 like rocker at the bottom. The telegram when opening the two control contacts is identical to that of the radio button. Several radio transmission modules must not be simultaneously controlled. The universal control voltage at +An/-A2 processes control commands from 8 to 253V AC or 10 to 230V DC with a length of at least 0.2 seconds. Maximum parallel capacity of the control lines at 230V 5nF. This corresponds to a length of about 20 meters. If the terminals A1 and A3 are connected to a bridge, a spark telegram of A3 is transmitted 1× per minute as long as the control voltage is applied. For example, for central commands with priority. No constant power supply required, therefore no stand-by loss. The rotary switch is used for activation or. Deactivation of the encryption is required and is in operation on AUTO. Enable encryption: Turn the rotary switch to right stop (position key) and once buttons. Disable encryption: Turn the rotary switch to left stop (position of broken key) and once buttons. Number of commands: 2 Rolling code system: No Radio hand transmitter: No Radio button under plaster: No Radio button on plaster: No Radio coder: Yes Keyboard protection cover: No

If a plurality of installation relays are permanently excited, ensure sufficient ventilation according to the power loss calculation. The spacer increases a distance from the neighboring device of 9 mm. Distance piece for the production and maintenance of a ventilation distance in the case of very warm series installation devices, e.g. dimmers from 300W/400W and continuous electromechanical current surge switches. Width: 9 mm Depth: 55 mm Height: 80 mm

Switching relay for mounting on support rails DIN-EN 60715 TH35 rated switching power 16 A/250 W AC or. 10 A/400 W AC Electromechanical switching relay with manual actuation and switching position display. Switch-on time 100%. Control power requirement 1.9W. Contact distance 3mm. Test voltage Contact/contact 2000W and test voltage control connections/contact 4000W. Number of contacts as closer: 1 Voltage type for actuation: AC TLE: 1 Rated control voltage Us at AC 50 Hz: 12 - W