Eltako

Mounting type: other protection type (IP): IP20 Max. switching current: 10 A Max. Switching power: 2000 W Max. Number of switching outputs: 1 Bus system EIB/KNX: No Bus system Funkbus: Yes Bus system Powernet: No Bus connection included: Yes Bus system LON: No Other bus systems: without on-site/hand operation: Yes With LED display: Yes C load: Yes Rated current: 10 A Rated operating voltage: 230 - 230 W Different phases connectable: No Modular expansion option: No 1 lock not potential-free 10A/250V AC, light bulbs 2000 Watt, ESL and LED up to 400 Watt. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.8 Watt. Intermediate plug for German protective contact socket. With increased contact protection. Supply and switching voltage 230W. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. After insertion, wait for the automatic short synchronization before the switched consumer is inserted. This radio actuator has the most modern hybrid technology we have developed: We have combined the wear-free reception and evaluation electronics with a bistable relay. From the manufacturing week 11/14, encrypted sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each state change and the central control telegrams received are then confirmed with a radio telegram. This radio telegram can be taught in other actuators, the GFVS software and in universal displays. With the left button LRN up to 35 radio buttons are assigned, either as a universal probe, direction probe or central control probe. Up to 35 radio-window door contacts FTK or radio-airport window handles can be learned for the control of extractor hoods or the like. Several FTK or radio hopper window handles are linked. Will an FTK or radio

Wireless Switch: Universal Dimming Switch for Built-in and AP Mounting, Universal Dimming Switch for R, L and C Loads, Automatic Lamp Detection, with which the % Rotary Switch can set the minimum brightness (full dimming) with the dim-speed Rotary Switch can set the dimming speed, automatic electronic overload protection and overtemperature switch. Automatic lamp detection. Stand-by-loss only 0.7 Watt. Minimum brightness or dimming speed adjustable. With children's room, slumber and light alarm. In addition to light scene control. Encrypted radio, bidirectional radio and repeater function can be switched on. For installation. 45mm long, 45mm wide, 33mm deep. Universal dimming switch for lamps up to 300W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Supply, switching and control voltage locally 230W. No minimum load required. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. car

Powerline sensor input for mounting in 58 mm switch boxes, powerline sensor input with 1 channel, sensor input 230W, stand-by loss only 0.5 Watt. For controlling and switching at various points. Number of inputs: 1 Powerline sensor input with 1 channel. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. Sensor input 230W. Stand-by loss only 0.5 Watt. For controlling and switching at various points. The sensor input acts on all actuators with the same address or as a central probe when the element address 0 is used. For address assignment there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above it there is a sliding switch as a configuration switch with the positions 0, 1 and 2. On the left of the rotary switches there is a red LED that displays all activities. In addition, the reset button and on the right there is a service pin. Functions according to user manual. The above connection terminals are plug terminals for conductor cross sections from 0.2mm2 to 1.5mm2.

Radio transmitters the batteryless remote control contains 2 same radio modules as the radio button FT4 and has 2 double rockers, therefore it is possible to send 8 evaluable radio telegrams Color: aluminum anthracite Number of channels: 8 Window transmitters: No Suitable for display element: No Hand transmitter: Yes Wall transmitter: No Remote control: Yes Halogen-free: Yes Finishing of the surface: matte. The batteryless remote control contains two identical radio modules and has 2 double rockers. 8 evaluable radio telegrams can therefore be sent. A wall bracket WHF-al and 2 pieces stainless steel countersink screws 2.9x25mm and dowel 5x25mm are included for wall mounting. The rockers can be simply pulled off and replaced by laser-engraved rockers.

Radio antenna module for mounting on support rail DIN-EN 60715 TH35, forwards all radio signals addressed to downstream radio actuators in its receiving area, mini-USB for connecting a PC for creating a device list, for configuring the actuators using the PCT14 PC tool and for data backup, supply voltage 12V DC radio antenna module for the Eltako-RS485 bus with interchangeable antenna. With integrated power supply 12V DC/8W. Bidirectional. Encrypted radio. Stand-by-loss only 1 watt. If required, a radio antenna FA250 or FA200 can be connected. Row mounting device for mounting on support rail. 36mm wide, 58mm deep. Supply voltage 230V. Included are 2 terminal resistors for mounting with imprint, 1/2 TE, 3 plug-in bridges 1 TE (including 1 replacement), 2 plug-in bridges 1/2 TE (including 1 replacement) and a plug-in bridge mounting tool SMW14. The radio antenna module FAM14 receives and checks all signals from the radio transmitters and repeaters in its reception area. These are passed through an RS485 interface to downstream RS485 bus switch actuators: Up to 126 channels can be connected to the RS485 bus. Bus and power supply with plug-in bridge. At the last actuator, the adjacent second terminal resistor must be plugged on. Up to 128 encrypted sensors can be learned. Mini USB to connect a PC to create a device list, to configure the actuators using PCT14 and to backup data. A legalization code for downloading the PCT14 from the Eltako-Homepage www.eltako.de is attached to FAM14. With a load greater than 50% of the rated power of 8W, half a division unit is required for ventilation with the spacer DS14 on the left side. TLE: 2 radio frequency: 868 MHz

Powerline actuator for mounting in 58 mm switch boxes, Powerline actuator with 1 channel. Suitable as current surge switches or relays. 1 lock not potential-free 10A/250V AC, light bulbs 2000 Watt. Powerline actuator with 1 channel. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. Suitable as current surge switches or relays. 1 lock not potential-free 10A/250V AC, light bulbs 2000 Watt. Sensor input 230W. Stand-by loss only 0.5 Watt. For controlling and switching at the same point. For address assignment there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above it there is a sliding switch as a configuration switch with the positions 0, 1 and 2. On the left of the rotary switches there is a red LED that displays all activities. In addition, the reset button and on the right there is a service pin. Functions according to user manual. The above connection terminals are plug terminals for conductor cross sections from 0.2mm2 to 1.5mm2. Max. switching current: 10 A Max. Switching power: 2000 W Max. Number of switching outputs: 1 Bus system EIB/KNX: No Bus system Funkbus: No Bus system Powernet: Yes Bus coupling included: Yes Bus system LON: No Other bus systems: without LED display: Yes C load: Yes Various phases connectable: No Modular expansion option: No

Powerline actuator for mounting in 58 mm switch cans,Powerline actuator with 2 channels, can be used as a power surge switch or relay. 1+1 lock not potential-free 5A/250V AC, incandescent lamps 1000 Watt. 2 sensor inputs with internal low voltage. Stand-by loss only 0.5 Watt. For controlling and switching at the same point. Powerline actuator with 2 channels. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. Suitable as current surge switches or relays. 1+1 lock not potential-free 5A/250V AC, incandescent lamps 1000 Watt. 2 sensor inputs with internal low voltage. Stand-by loss only 0.5 Watt. For controlling and switching at the same point. Use only potential-free switching elements. Internal low voltage at the sensor inputs. For address assignment there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above it there is a sliding switch as a configuration switch with the positions 0, 1 and 2. Position 0: sensor inputs act as a pushbutton (current pushbutton switch). On the left of the rotary switches there is a red LED that displays all activities. In addition, the reset button and on the right there is a service pin. Functions according to user manual. The above connection terminals are plug terminals for conductor cross sections from 0.2mm2 to 1.5mm2. In addition, there are three strands with core end sleeves for the two control inputs with internal low voltage. Max. switching current: 5 A Max. Switching power: 1000 W Max. Number of switching outputs: 2 Bus system EIB/KNX: No Bus system Funkbus: No Bus system Powernet: Yes Bus coupling included: Yes Bus system LON: No Other bus systems: without LED display: Yes C load: Yes Various phases connectable: No Modular expansion option: No

Powerline blind actuator for controlling and switching at the same location, only use potential-free switching elements, internal low voltage at the sensor inputs. The control inputs can be used for a blind button or a blind switch. The runtime is preset at 120 seconds and can be changed with the installation software SIENNA-Professional. Powerline blind actuator for 1 motor. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. 1+1 lock for motors up to 3A. 2 sensor inputs with internal low voltage. Stand-by loss only 0.5 Watt. For controlling and switching at the same point. Use only potential-free switching elements. Internal low voltage at the sensor inputs. The control inputs can be used for a blind button or a blind switch. The runtime is preset at 120 seconds and can be changed with the installation software SIENNA-Professional. For address assignment there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above it there is a sliding switch as a configuration switch with positions 0.1 and 2. On the left of the rotary switches there is a red LED that displays all activities. In addition, the reset button and on the right there is a service pin. Functions according to user manual. The above connection terminals are plug terminals for conductor cross sections from 0.2mm2 to 1.5mm2. In addition, there are three strands with core end sleeves for the two control inputs with internal low voltage. Max. number of blind exits: 1 Number of entrances: 2 Power type: AC Bus system EIB/KNX: No Bus system Funkbus: No Bus system Powernet: Yes Bus coupling included: Yes Max. Switching power: 650 W Switching current ohmsch: 3 A Bus system LON: No Other bus systems: without

Powerline sensor input for mounting in 58 mm switches, powerline sensor input with 8 channels, 8 sensor inputs with internal low voltage. Stand-by loss only 0.5 Watt. For controlling and switching at various points. Powerline sensor input with 8 channels. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. 8 sensor inputs with internal low voltage. Stand-by loss only 0.5 Watt. For controlling and switching at various points. Use only potential-free switching elements. Internal low voltage at the sensor inputs. For address assignment there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above it there is a sliding switch as a configuration switch. Position 0: 2 adjacent inputs as a directional sensor for AUF/AB or ON/OFF. On the left of the rotary switches there is a red LED that displays all activities. In addition, the reset button and on the right there is a service pin. Functions according to user manual. The above connection terminals are plug terminals for conductor cross sections from 0.2mm2 to 1.5mm2. The addresses of the 8 inputs can also be freely assigned with the installation software SIENNA-Professional. The upper sleeve strip with 9 strands with core end sleeves is plugged. 8 control inputs with internal low voltage. Number of inputs: 8

Protection type (IP): IP20 Radio frequency: 868 Mhz Range: 30 m Number of commands: 2 Power supply: other Rolling code system: No Radio transmitter: No Radio button under plaster: No Radio button on plaster: Yes Radio coder: No Radio-Hoppe window handles Secusignal series Atlanta with integrated radio transmitter module, battery- and wireless. Create the radio telegrams even when opening, tilting and closing the windows. The complete assembly material is included. The radio sensor can be learnt in the following actuators and in the building radio visualization and control software: F2L14, F4HK14, FGM, FHK14, FHK61, FMZ14, FMZ61, FSB14, FSB61, FSB71, FSG14, FSR14, FSR61, FSR71, FUA FDD14 FUTH.

Universal dimming switch for installation in the 230V power supply line, for example in intermediate ceilings and luminaires, universal dimming switch, Power MOSFET up to 400W, automatic lamp detection. Minimum brightness and dimming speed adjustable. With children's room, slumber and light alarm circuit as well as constant light control and master-slave operation. In addition with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by-loss only 0.7 Watt. Number of commands: 32 Material quality: Thermoplastic Finishing of surface: matt Suitable for dimmer: Yes Suitable for pulse pushers: No Suitable for roller shutter switch: No Suitable for switch: No Rolling code system: Yes In the case: Yes In the tube socket housing: No As module/plate: No Tasting operation: Yes Switching operation: No With radio hand transmitter: Yes With radio encoder: No. Automatic lamp detection. Minimum brightness and dimming speed adjustable. With children's room, slumber and light alarm circuit as well as constant light control and master-slave operation. In addition with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by-loss only 0.7 Watt. Mounting into the 230V power supply line, for example in intermediate ceilings and luminaires. 166mm long, 46mm wide and 31mm deep. With cable load. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness

Blister-Pack Switching includes a battery-free and line-free, radio button F4T65 in pure white gloss, as well as a switch actuator FSR61-230V, with power surge switch function Blister-Pack Switching includes a battery-free and line-free radio button F4T65 in pure white glossy and a switch actuator FSR61-230V with power surge switch. F4T65-wg: radio button for single mounting 84x84x16mm or mounting in the e-design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1E, a rocker, a double rocker, a fastening frame, a holding plate, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. The radio sensor illumination FTB can then also be latched from behind to the holding plate. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then the holding plate - with the