Eltako

Radio-Dimmaktor Tipp-Funk® Universal-Dimmaktor, with Power MOSFET 230 V-Glüh- and halogen lamps up to 300 W, 230 V-LED up to 100 W, no inductive (wound) transformers, with children's room and slumber circuit, no minimum load, stand-by loss only 0.7 W, it can be possible to. With Power MOSFET. 230V-Glüh- und Halogen-Lampen bis 300W, 230V-LED bis 100W. No inductive (wound) transformers. With children's room and slumber circuit. No minimum load. Stand-by-loss only 0.7 Watt. With the comfortable Tip-Funk® technique, up to 24 radio universal probes, radio direction probes, radio central control probes and motion sensors TF-BSB can be learned. In addition, the actuator can be locally controlled with a conventional 230V controller without a glow lamp current. When learning, the dimmactor can be set to phase-section in order to allow optimum dimming with different LEDs.

Radio actuator power surge relays for installation and AP installation, 1 locks potential-free 10 A /250W AC, incandescent lamps 2000 Watt, power surge switch with reverse deceleration, switch-off pre-warning and push button continuous light can be switched on, stand-by loss only 0.3 - 0.8 Watt. Material quality: Thermoplastic Finishing of the surface: matt Suitable for dimmer: No Suitable for pulse pushers: Yes Suitable for roller shutter switch: No Suitable for switch: Yes In the case: Yes In the tube socket housing: No As module/plate: No Touch mode: Yes Switch mode: Yes With radio hand transmitter: Yes With radio code: No With radio button: Yes Suitable for blind switch: No Suitable for blind switch: No. 1 Locker potential-free 10A/250V AC, incandescent lamps 2000 Watt, downtime delay with switch-off warning and pushbutton continuous light can be switched on. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.3-0.8 watts. For installation. 45mm long, 45mm wide, 33mm deep. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. In addition to the radio control input via an internal antenna, this radio actuator can also be controlled locally by means of a conventional control probe mounted in front of it. A glow lamp current is not permitted. Encoded sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each state change and the central control telegrams received are then confirmed with a radio telegram. This radio telegram can be learned in other actuators such as FSR61NP-230V, GFVS software and universal displays.

Radio actuator power surge relays for can installation, installation and AP mounting, 1 closer not potential-free 10 A /250W AC, incandescent lamps 2000 W, reverse deceleration with switch-off warning and push-button continuous light can be switched on, stand-by loss only 0.8 W radio actuator power surge relay 230W. 1 Locker not potential-free 10A/250V AC, incandescent lamps 2000 Watt, fallback delay with switch-off warning and button permanent light can be switched on. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.8 Watt. For installation. 45mm long, 45mm wide, 33mm deep. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. In addition to the radio control input via an internal antenna, this radio actuator can also be controlled locally by means of a conventional 230V control probe mounted beforehand. A glow lamp current is not permitted. Encoded sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each state change and the central control telegrams received are then confirmed with a radio telegram. This radio telegram can be taught in other actuators, the GFVS software and in universal displays. Scene control: A plurality of FSR61 can be switched on or off to form a scene with one of the four control signals of a pushbutton learned as a scene scanner. With the upper rotary switch, up to 35 radio buttons are assigned in the LRN position, one or more central control buttons thereof. In addition, radio window door contacts with the function closer or opener with opened window, radio-outside brightness sensors FAH and radio motion detector FBH. Then the desired function of this current surge switch

Radio actuator heating-cooling relay for can installation, 1 closer potential-free 10A/250V AC. Stand-by loss only 0.3-0.8 watts. For installation. 45mm long, 55mm wide, 33mm deep. Supply voltage 230 W or 8 to 24 W UC. Radio actuator heating cooling relay 230W. 1 Locker potential-free 10A/250V AC. Stand-by loss only 0.8 Watt. Encrypted radio, bidirectional radio and repeater function can be switched on. For installation. 45mm long, 45mm wide, 33mm deep. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. This heating-cooling relay evaluates the information from radio temperature controllers or sensors. Optionally complements window door contacts, motion detectors, hoppe window handles and radio buttons. Valves are controlled with the potential-free working contact. From the manufacturing week 11/14, encrypted sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each function change (normal operation, lowering operation, out) is confirmed with a radio telegram. This radio telegram can be learned in the GFVS software. Upper rotary switch for operating modes. The LED accompanies the learning process according to the user manual and displays radio control commands during operation by short flashing. Mounting type: Approval Radio frequency: 868 Mhz Colour: blue Material: plastic Halogen-free: Yes Material quality: thermoplastic Finishing of surface: matt Suitable for dimmer: No Suitable for pulse pushers: No Suitable for roller shutter switch: No Suitable for switch: No In the case: Yes In the tube socket housing: No As module/plate: No Touch operation: No Switching operation: No With radio hand switch: Yes

Radio power surge relays for installation in the 230 V power supply line, 1 closer not potential-free 16 A/250 W AC, incandescent lamps 2000 W, with light scene control via PC or with radio driver, encrypted radio, bidirectional radio and repeater function connectable, stand-by loss only 0.8 Watt power surge relay 1 closer not potential-free 16A/250V AC, incandescent lamps. With light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.8 Watt. Mounting into the 230V power supply line, for example in intermediate ceilings and luminaires. 166mm long, 46mm wide and 31mm deep. With cable load. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. Scene control: With one of the four control signals of a pushbutton learned as a scene scanner with a double rocker, a plurality of FSR71NP can be switched on or off to one scene in each case. Central commands on the PC are sent with the building radio visualization and control software GFVS. Learn one or more FSR71NP on the PC. With the rotary switches, the probes are learned and, if necessary, the device is tested. For normal operation, the middle and lower rotary switches are then set to AUTO. The LED under the upper rotary switch accompanies the learning process according to operating instructions and displays control commands during operation by short flashing. Number of relays: 1 Number of commands: 32 Material quality: Thermoplastic Finishing of the surface: matt Suitable for dimmer: No Suitable for pulse pushers: Yes Suitable for roller shutter switches: No Suitable for switches: Yes In the case: Yes In the tube socket housing: No As module/plate: No Tasting operation: Yes Switching operation: Yes With radio hand transmitter: Yes

Radio actuator multifunction power surge switch for installation and AP mounting, 1+1 closer not potential-free 10 A /250W AC, incandescent lamps 2000 W, stand-by loss only 0.9 W, with the upper rotary knob several different power surge switch functions can be selected, second rotary switch is required for learning the radio transmitters. Material quality: Thermoplastic Finishing of the surface: matt Suitable for dimmer: No Suitable for pulse pushers: Yes Suitable for roller shutter switch: No Suitable for switch: Yes In the case: Yes In the tube socket housing: No As module/plate: No Tasting operation: Yes Switching operation: Yes With radio hand transmitter: Yes With radio coding device: No With radio button: Suitable for blind switch: No Suitable for blind switch: No. 1+1 lock not potential-free 10A/250V AC, light bulbs 2000 Watt. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.8 Watt. For installation. 45mm long, 45mm wide, 33mm deep. Supply, switching and control voltage locally 230W. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. This radio actuator as a multifunctional power surge switch has the most modern hybrid technology we have developed: We have combined the wear-free reception and evaluation electronics with two bistable relays which switch in the zero passage. As a result, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. In addition to the radio control input via an internal antenna, this multi-function current surge switch can also be locally controlled with a conventional 230V control probe installed beforehand. maximum current as a sum of both contacts 16A

Radio actuator power surge group switch for installation and AP mounting, 1+1 closer not potential-free 10A/250V AC, for roller shutters and shading elements, stand-by loss only 0.8 Watt, switching and control voltage 230W radio actuator 230W. 1+1 lock not potential-free 4A/250V AC, for roller shutters and shading elements. Encrypted radio, bidirectional radio and repeater function can be switched on. Stand-by loss only 0.8 Watt. For installation. 45mm long, 45mm wide, 33mm deep. Supply, switching and control voltage locally 230W. If the supply voltage fails, it is switched off in a defined manner. In addition to the radio control input via an internal antenna, this radio actuator can also be controlled locally by means of a conventional 230V control probe mounted beforehand. Encoded sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each state change and the central control telegrams received are then confirmed with a radio telegram. This radio telegram can be taught in other actuators, the GFVS software and in universal displays. With the upper rotary switch, up to 35 radio buttons are assigned in the LRN position, one or more central control buttons thereof. The desired function of this current surge group switch is then selected: GS1 = group switch with pushbutton control and drop delay in seconds. It is possible to learn both a radio button with the function of up-hold-down stop as a universal probe such as the local probe, and also a radio button such as a roller shutter double probe as a directional probe with up-press up and down press down. Short tipping immediately interrupts the movement. Central control can be performed dynamically with and without priority. The LED accompanies the learning process according to the user manual and displays radio control commands during operation by short flashing. Mounting type: Aufputz Integrated timer: No Mi

short stroke probe wg pure white glossy, 4 closers 8A/250V AC, contact distance 0.5mm, 80x80mm outside, frame internal dimensions 55x55mm, 15mm high. Included are the frame R, a large rocker W, a double rocker DW, an intermediate frame ZR (all the same color), the holding plate HP and the probe module. Mounting via a 55mm switch box. For screw fastening on 55mm switch cans we recommend sheet metal counter screws 2,9x25mm, DIN 7982 C. The unprinted double rocker is snapped onto the probe module. If these are to be exchanged for the large unprinted rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the probe module on the rear side. The Eltako-Frame can be installed at any time against a frame with internal dimensions 55x55mm of other manufacturers are exchanged. Color: white Halogen-free: Yes Text field/description area: Yes Feedback contact: No Number of actuators: 2 With lighting: No Surface: Other surface design: glossy Rated voltage: 230 V

Universal dimming switch with rotary knob, Power MOSFET up to 800W. Automatic lamp detection. Stand-by loss only 0.2 Watt. Minimum brightness and maximum brightness adjustable. DIN-EN 60715 TH35 for mounting on support rail. 2 division units = 36 mm wide, 58 mm deep. Universal dimming switch for lamps up to 800W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230V LED lamps additionally depending on the lamp electronics. Up to 3600W with power inputs LUD12 at the terminals X1 and X2. Universal control voltage 8..230V UC Mounting type: REG Color: blue Operation type: rotary knob Halogen-free: Yes Composition: other load type: universal Serial dimmer: No Conveyor input: No Light value store: Yes Applicable with button: Yes Applicable with motion detector: No Applicable with presence detector: No Applicable with timer/timer: No Applicable with radio button: No. Automatic lamp detection. Stand-by loss only 0.2 Watt. Minimum brightness and maximum brightness adjustable. DIN-EN 60715 TH35 for mounting on support rail. 2 division units = 36mm wide, 58mm deep. Universal dimming switch for lamps up to 800W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230V LED lamps additionally depending on the lamp electronics. Up to 3600W with power add-ons LUD12 at the connections X1 and X2. Universal control voltage 8..230V UC, galvanically isolated from supply and switching voltage 230W. No minimum load required. PWM control with 10-24V DC to d

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. 84x84x16mm
or assembly into the e-design switch system. Pure white glossy
With Power MOSFET. 230V and halogen lamps up to 300W,
230V LED lamps up to 100W. No inductive (wound) transformers.
With children's room and slumber circuit. With integrated universal
Direction sensor and connection for additional conventional probes.
Stand-by-loss only 0.7 Watt.

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. For single mounting 80x80x15/33mm
or assembly into the 55s switch system. Pure white glossy
With Power MOSFET. 230V and halogen lamps up to 300W,
230V LED lamps up to 100W. No inductive (wound) transformers.
With children's room and slumber circuit. With integrated universal
Direction sensor and connection for additional conventional probes.
Stand-by-loss only 0.7 Watt.

Radio actuator for installation, dimming switch for LED 12-36V DC, up to 4A, stand-by loss only 0.2-0.4 Watt, minimum brightness and dimming speed adjustable, with children's room and slumber circuit, additionally with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function connectable PWM dimming switch for LED 12-36VDC, up to 4A stand-by loss only 0.2-0.4 Watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. In addition with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function can be switched on. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage 12 to 36V DC, depending on the connected LED illumination. Output voltage PWM (pulse-width modulation). Output current max. 4A. A pulse-resistant DC power supply is required which supplies the required voltage and the required current of the LED lamp(s). Universal control voltage 8..230V UC, galvanically isolated from the supply and switching voltage. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. From the manufacturing week 11/14, encrypted sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. With the upper %Lampe The minimum brightness (fully dimmed) can be set. In the LRN position, up to 35 radio buttons are assigned, one or more central control buttons thereof. The dimming speed can be set with the lower dim speed rotary switch. In addition to the radio control input via an internal antenna, this dimming switch can also be equipped with an event