ABB

To control a maximum of four independent 24 W DC drives for positioning blinds, roller shutters, awnings and other hangings as well as for controlling doors, windows and ventilation flaps. With automatic driving time determination and manual operation directly on the device. Functions: On/off, lamella adjustment/stop, position and scene control, safety functions, sun protection and heating/cooling automatic, status messages.

For controlling a maximum of four 230 W AC independent drives for positioning blinds, roller shutters, awnings and other hangings, as well as for controlling doors, windows and ventilation flaps. With automatic driving time determination and manual operation directly on the device. No auxiliary voltage required. The outputs are interlocked electromechanically. Functions: On/off, lamella adjustment/stop, position and scene control, safety functions, sun protection and heating/cooling automatic, status messages.

The device records eight AC/DC signals in the voltage range of 10...230 V. The input state is displayed over 8 yellow LED’s. The binary inputs allow the detection of 8 independent input signals. Each channel has a button for manual operation. The devices are used by ABB i-bus® supplies and does not require additional power supply.

For switching and dimming light bulbs, 230V halogen lamps or low-voltage halogen lamps on wound or electronic transformers (automatic load detection). Output power 2x300 VA to 45 °C ambient temperature, as well as max. 500 VA if only one output is operated. Both outputs are independent of one another and can be fed from different phases. Extensive application program with scene and time functions.

Combined lightning and overvoltage protection device SPD type 1+2 for protection of low-voltage consumer systems against flash currents and overvoltages. Tested SPD type 1 and type 2 according to DIN EN 61643-11. The devices can be used for use as an overvoltage protection device according to WDE 0100 part 443 and part 534, as well as within the framework of the lightning protection zone concept. The devices are compatible with the System per M compact series. Optionally, the SPD is equipped with a floating contact. The variants with evacuation varistor – (s) offer an additional protection of the system in that at the end of the service life, the surge arrester is not completely separated from the network, but a basic protection is still guaranteed by an additional smaller varistor and the system is thus still protected until the surge arrester is replaced.

The device queries 8 potential-free contacts with internally generated interrogation voltage. The input state is displayed over 8 yellow LED’s. The binary inputs allow the detection of 8 independent input signals. Each channel has a button for manual operation. The devices are used by ABB i-bus® supplies and does not require additional power supply.

The KNX voltage supply 640 ma with diagnostic function and extended LED display generates and monitors the KNX system voltage (SELV). With the integrated throttle, the bus line is decoupled from the voltage supply. The voltage output is short-circuit-proof and overload-proof. The two-color LED indicates the status of the device. The device has an additional short-circuit-proof and overload-proof 30 W DC voltage output. This can be used for feeding a further bus line (in conjunction with a separate throttle). The voltage supply has a wide-range input for the supply voltage in the range 85Å265 W AC,50/60 Hz.

The ABB i-bus® KNX Line Coupler LK/S 4.2 is a series installation device with 2 TE module width. It is used as a line/range coupler or line amplifier. As a line coupler, the LK/S connects a line with a main line, as a region coupler a main line with a region line. It provides a galvanic separation. The group addresses of the main groups 14 . . . 31 can be filtered in conjunction with the ETS 4 .

Switches independent electrical consumers via potential-free contacts 8 ABB i-bus®. The manual operation of the contact is possible for each output. The switching state of the contact is displayed. The 16A-AC1 series is suitable for switching ohmic, inductive and capacitive loads.

Fault current protection devices (Rccbs) offer personal and property protection as well as protection against electrically ignited fires according to DIN WDE 0100-410 and DIN WDE 0100-530. The F200 series fault current protection switches ensure protection against sinusoidal alternating currents, pulsating currents and smooth direct fault currents. As well as fault protection (protection in indirect contact), additional protection (with I?n = 30 ma) and fire protection (with I?n = 300 ma). They meet product standards for type A IEC/EN 61008-1, 61008-2-1, 61543 (WDE 0664 10, 11, 30) and type B DIN EN 62423 (WDE 0664-40). Areas of application are predominantly in industrial and commercial applications. The extensive range of accessories offers you everything you need for your installation tasks. The RCCB type B is suitable for non-linear circuits that can generate fault currents with smooth direct fault currents and with different (high/) frequencies. These components are located in electronic operating means such as frequency converters. The RCCB type B has a frequency range of 0...2 khz to detect the fault current and offer a high system availability.

Combination device with 8 binary inputs and 8 switching actuators. Conventional probes or auxiliary contacts can be connected to 8 channels. The information of the contact query can be used for controlling Busch-free@home® actuators or for detecting status information. The contact interrogation voltage is provided by the device itself. Maximum cable length for cable cross section 1.5 mm2